84/96-1800 NG Performance Specifications
Exceptional Force * Reliable Results

Power Train
Engine	Caterpillar C7 ACERT, Tier III, Diesel, Water Cooled w/Electric Start
Rating	300 HP (223 kW)
Maximum Engine Speed	2100 RPM
Maximum Forward Engine Torque	858 ft-lbs 2100 RPM
Maximum Reverse Engine Torque	773 ft-lbs 2100 RPM
Fuel Capacity	50.5 U.S. Gallons (191 L)
Hydraulic Capacity	48 U.S. Gallons (181 L)
Battery	Two, Deka 634MF, 12 V,  690 CCA
Transmission
Type	Eaton FRO112106 – 10 Speed
Transmission Ratios	Gear Ratio 1St Gear 12.69:1 2ND Gear 9.29:1 3RD Gear 6.75:1 4th Gear 4.9:1 5TH Gear 3.62:1 6TH Gear 2.59:1 7TH Gear 1.9:1 8TH Gear 1.38:1 9th Gear 1.0:1 10th Gear 0.74:1  Reverse    13.75:1
Clutch	Dual Plate, Spring Applied w/ 16" (406 mm) Diameter Twin Disk/Hydraulically Assisted Clutch Actuator
Gearbox
Ratio	25.6:1
Torque & Speed
Torque Requirements	Gear Ratio Max. Speed 1st 272,236 ft lbs (369,103 Nm) 6 RPM 2nd 199,296 ft-lbs (270,128 Nm) 9 RPM 3rd 144,806 ft-lbs (196,330 Nm) 12 RPM 4th 105,119 ft-lbs (102,522 Nm) 17 RPM 5th 77,659 ft-lbs (105,291 Nm) 23 RPM 6TH 55,563 ft-lbs (75,333 Nm) 33 RPM 7th   40,760 ft-lbs       (55,263 Nm)                   45 RPM 8th 29,608 ft-lbs (40,139 Nm) 62 RPM 9th 21,453 ft-lbs (29,086 Nm) 85 RPM 10th 15,875 ft-lbs (21,523 Nm) 116 RPM Reverse 272,096 ft lbs (368,913 Nm) 6 RPM *These are net figures. A deduction has already been taken into consideration for hydraulic and mechanical loss
Hydraulic System
Maximum Thrust	1,800,000 lbs (816 Tonnes)
Hydraulic Pump	Axial Piston Pump w/Load Sensor
Gear Pump	39 CIR, LH, SAE
Maximum Pump Pressure	5000 psi (345 bar)
Maximum Pump Output	38 U.S. Gallons (144 L)/minute
Hydraulic Motors	Two, 60 CIR, LSHT
Hydraulic Push Bar Cylinder	One, 2” Bore x 2” Stroke (50.8 mm – 50.8 mm)
Hydraulic Clutch Cylinder	One, 1 ½” Bore x 4” Stroke                           (38.1 mm – 101.6 mm)
Hydraulic Thrust Cylinder	Four, 12” Bore x 35” Stroke                             (304.8 mm – 889 mm)
Hydraulic Suction Strainer Filter	Suction Strainer w/ 149 Mesh Screen
Hydraulic Return Filter	High Pressure Return Filter to 6 Micron ABS w/Replaceable Element
Misc. Performance Data
Working  Range	24 – 96 inch (610 mm  – 2,438 mm)                  Casing Diameter
Hex Drive	6 inch (152.4 mm)
Quik Split™	Quik Tran™
The Quik Split™ frame design, allows the machine to be separated into sections to accommodate lighter and fasters lifts into and out of the bore pit, and aids the operator in being able to facilitate better and safer machine positioning	Quik Tran© is the fast return system, made available exclusively from American Augers, as it provides up to 20,000 lbs (9,072 kg) of push/pull at high speed, and there will be no dogging or winching during retract, as the Quik Tran system engages directly to the machine track. Quik Trans benefit will be easier and faster machine operation in challenging work climates or conditions
Spoil Door
With a Safety-First commitment, all American Augers horizontal earth boring machines are equipped with a gravity activated-manual spoil door, which deflects thrown debris from the spoil chamber
Dimensions
Length	17’ (5.18 m)
Width	9’ 2” (2.79 m)
Height	8’ 6” (2.6 m)
Master Track Length (Three Section Assembly)	Total Assembly: 24’ (7.31 m) One, 8’ (2.4 m) section w/1 1/2” (38 mm) back plate Two, 8’ (2.4 m) sections
Extension Track Length	Two, 8’ (2.4 m) sections
Weight
Base Unit ( Split Weight)	15,000 lbs (6,804 kg)
Power Pack ( Split Weight)	17,000 lbs (7,711 kg)
Master Pusher	3,220 lbs (1,461 kg)
Master Track	6,000 lbs (2,722 kg) each
Lifting Sling	900 lbs (408 kg)
Total Weight	42,120 lbs (19,105 kg)
Extension Track	6,000 lbs (2,722 kg) each
Master Saddle	400  lbs (181.44 kg)

(*Note All product performance specifications, components, weights, dimensions, and other related information is subject to change without notice from the manufacturer)